Links to everything you need to screen print your own t-shirts: http://www.iliketomakestuff.com/how-to-screen-print-your-own-t-shirts
Visit Casper.com/make and use the code MAKE for $50 off
Here’s what you’ll need:
(purchasing via these affiliate links supports ILTMS)
Photo Emulsion Kit (includes emulsion remover) – http://amzn.to/1JxIf3e
Screen Printing Ink (white) – http://amzn.to/1bzCCTH
Squeegee (multiple sizes) – http://amzn.to/1IiZ5S0
Aluminum Screen (23″x31″) – https://amzn.to/2QFsRcH
Palette Knife – http://amzn.to/1bzDcAY
Blank t-shirts – http://amzn.to/1zjGhAl
MORE PROJECTS, POSTS AND EVENTS
Want to support ILTMS? There are lots of ways .. find out more at
BUY A SHIRT, STICKER OR A HANDMADE ITEM!!
Tweets by iliketomakestuf
Screen printing is a fantastic way to cheaply make branded items, or even one off custom pieces. Need a silly t-shirt to surprise a friend with? Printing it yourself is the cheapest way to make that happen! Kids can even get the hang of printing VERY quickly and be apart of the entire process, which is awesome!
Here are a few things that I didn’t cover in the video that I think will give you better results.
Use high dpi screens. These provide finer detail, and have significantly improved my prints.
Have someone hold your frame so that you can use two hands to evenly pull the squeegee.
If you don’t have access to a dryer for heat setting, you can cover the print with a piece of paper and iron it for a minute.
If using a dark material, look for an ink labeled “super opaque”. You’ll get a brighter colored print.
You’ll need a screen and squeegee to start.
Also, some photo emulsion for screen printing.
Add water to the sensitizer, then mix it with the emulsion.
Mix thoroughly until it’s an even green color.
Pour just a small amount onto the screen.
Use the squeegee to spread it evenly on both sides of the screen. Try to get even and full coverage by alternating directions and sides.
Dry the emulsion in front of a fan and IN THE DARK.
After it’s dry, quickly lay your artwork, backwards, on the back of the screen. You can print your art on transparencies at most office supplies stores or copy centers.
Tape the art in place, then lay on a piece of glass to hold it against the screen.
Apply a very bright light for 30-45 minutes.
You can also use sunlight, but the time may vary depending on cloud cover and placement.
The areas covered by your art do not get exposed when you remove the transparency.
Use a light spray and soft toothbrush to wash out the unexposed emulsion.
Be careful not to use too much force when spraying it out or you will remove emulsion around your design as well.
Use painters tape to mask any areas that you don’t want to print yet, or areas where the emulsion isn’t intact.
Layout your shirt on smooth, flat surface and remove wrinkles.
Place your design where you want it to be printed.
Lay a thick bead of ink above the art, extended past both ends. Be sure to add extra ink above large areas to be printed.
Even though I’m working alone here, you’ll have better luck to have someone hold your screen, then use two hands to evenly pull the squeegee fully across your screen.
Remove the screen and wash out all of the ink before it dries. After the ink dries, run your shirt through a clothes dryer for 5 minutes to heat set the print.
The screens can be reused by cleaning them with emulsion remover.
Spread a small amount across both sides of the screen.
Then use a hose to wash out the emulsion until the screen is clean. Dark inks will stain the material of the screen, but this will not affect future prints. Just make sure to remove all of the emulsion. Second channel: bit.ly/iltms-2